AGMA 2015-1-A01 PDF

racy documents correlate as shown in Figure 1. Current Status of New Standards. In late , the new tangential accuracy stan- dard ANSI/AGMA A AGMA A01 (R). Accuracy Classification System – Tangential Measurements for Cylindrical Gears. standard by American Gear. CONTAINS ANSI/AGMA A ACCURACY CLASSIFICATION SYSTEM- TANGENTIAL MEASUREMENTS FOR CYLINDRICAL GEARS AND AGMA.

Author: Arashimi Zujinn
Country: Nepal
Language: English (Spanish)
Genre: Music
Published (Last): 17 February 2012
Pages: 171
PDF File Size: 9.85 Mb
ePub File Size: 14.27 Mb
ISBN: 509-5-75834-617-7
Downloads: 35725
Price: Free* [*Free Regsitration Required]
Uploader: Nilmaran

Tolerance formulas were based on the actual gear geometry rather than on geometric mean values. Definitions and allowable values of deviations relevant to flanks of gear teeth. AGMA membership approved the adoption in August That parameter observes only the deviation in position of the first and last teeth of each sector of k pitches. Master gears shall conform to clause 7 tolerances, for accuracy grade 2, 3 or 4.

Gears made in quantity may be inspected at various steps in their manufacturing process on a sampling basis.

A New Standard in Gear Inspection

First, 2051-1-a01 formulas can be computer based to provide easy and accurate calculations of the gear tolerances. This test can include the effect of tooth element variations, such as a variation in helix. You may delete a document from your Alert Profile at any time. In such a case, the purchaser must agree on the details of the additional specifications concerning how the matching is to be performed and verified. Measurements taken in this direction have the following characteristics: Additionally, the formulas stated the tolerances in both U.

See clauses 1 and 4. This specified direction, called the tolerancing direction, may be normal to that surface, inclined at some angle, or along the arc of a specified circle. It specifies definitions for gear tooth accuracy terms, the structure of the gear accuracy grade system, 2015-1-a001 allowable values. Example of statistical process control SPC application. It is a complete revision, including accuracy grades, in order to be more compatible with ISO.


The profile slope deviation is deemed to be positive and the corresponding pressure angle deviation is deemed to be negative when the mean profile line shows an increase in material toward the tooth tip, relative to the design profile. We have no amendments or corrections for this standard.

The manufacturing of gearing to a specified accuracy may or may not include specific measurements.

Table 3 – Reference for methods and tolerances Parameter symbol Elemental: Tolerance system development and comparison. It is assumed that these measurements are representative of all the teeth on the gear.

Thus, a condition wherein the actual tooth flank position was nearer to the adjacent tooth flank than the theoretical position would be considered a minus — deviation.

The use of the accuracy grades for the determination of gear performance requires extensive experience with specific applications. Typically, the factor for this adjustment is the cosine of the angle between the normal direction and the specified tolerancing direction. All standards are subject to revision, and parties to agreements based on this American National Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below.

Tolerance values for gears outside the limits stated in this standard should be established by determining the specific application requirements. In either case, index values must first be found.

A New Standard in Gear Inspection | Gear Solutions Magazine Your Resource to the Gear Industry

Distinction agja made as to the direction and algebraic sign of this reading. It is possible that a specific gear can aga through the entire production process without ever having been measured.

This clause presents considerations for control of the various phases of manufacturing, including the recommended methods of measurement control. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. For example, when testing helix with a normal direction of measurement within the base tangent plane the measurement values must be divided by the cosine of the base 2015–1-a01 angle to compensate those values to the transverse plane as required by clauses 3 and 7.


If the document is revised or amended, you will be notified by email.

Item Detail – ANSI/AGMA ISO B14

The acceptability is characterized by periodic variation in sound during each revolution, or high levels of noise. The variables include module, mn, tolerance diameter, dt, and quality, A. The matching process for such gears 20115-1-a01 as pairs assumes greater importance than the individual absolute measurements.

It was approved as an American National Standard on September 30, Gear design is beyond the scope of this standard. It evaluates that portion of the gear tooth surface which actually makes contact with its mate.

Ten accuracy 20115-1-a01 are provided in this standard, numbered A2 through A11 in order of decreasing precision.

It provides information on minimum requirements for accuracy groups as well as gear measuring practices.

Two general types of mathematical filter are commonly available. These tolerances are applicable to the following 2015-1-s01 In applications that require inclusion of this very high frequency data, smaller probe tip radii can be specified.

Roll path length is an alternative to roll angle for specification of selected diameter positions on an involute profile. To determine the manufacturing requirement, the following starting recommended: If improved performance is desired, modifications of material, heat treatment, and accuracy level should be considered.

It is developed by subtracting the ordinates of a straight–line gradient from the ordinates of the design helix.