The main source of information is the DejaGnu user guide by Rob Savoye [3]. The most useful section is the Unit Testing API, which lists all the procedures. Follow these instructions as closely a possible in order get a good insight into how DejaGnu works, else you might run into a lot of subtle problems. You have. DejaGnu uses the GNU autoconf to configure itself. For more info on using autoconf, read the GNU autoconf manual. To configure, execute the configure.

Author: Bram Gardaran
Country: Uzbekistan
Language: English (Spanish)
Genre: Business
Published (Last): 21 April 2008
Pages: 214
PDF File Size: 5.92 Mb
ePub File Size: 13.60 Mb
ISBN: 145-9-44526-253-4
Downloads: 31167
Price: Free* [*Free Regsitration Required]
Uploader: Ganos

The expect language 2. When we replaced it with the Expect-based framework, it was like DejaGnu all over again The main source of information is the DejaGnu user guide by Rob Savoye [3]. The important thing to remember is that this means the configuration files are only read once, dsjagnu once for each test.

Command line option variables (DejaGnu)

Using DejaGnu with autoconfautomake and libtool. There are a number of options which are manhal documented in the manual. If as is usual the command takes more than one line, the arguments must be surrounded by braces.

DejaGnu configuration files 3. Expect is a program that “talks” janual other interactive programs. In general any pattern starting with ‘-‘ should be protected using -gl to future proof against new flags. Write any test programs and compile them.


runtest(1) – Linux man page

Value of the variable is incremented for each time it appears on the command line. Tests are usually written in expect using Tcl, but you can also use a Tcl script to run a test suite that is not based on expect. These definitions specify the output of a test case:. Writing a test is a matter of spawning the test program, then using the expect to match the output and report failure as appropriate.

It is important to understand two aspects of expect command behavior.

By convention the tests are all run from a directory named testsuitebut this need not be the case. Where an option is set both on the command line and in a configuration file, the command line will take precedence.

Don Libes introduced expect in his paper expect: DejaGnu supports the use of all five output messages; in this sense a test suite that uses exactly these messages can be considered POSIX conforming. However substitutions will still occur within these braces, unlike standard TCL. See section The files DejaGnu writes. One of the main things This command is used to send data to the standard input of a spawned process see spawn below.

Typically because the spawned process has completed execution. The directory containing test sub-directories and the tool specific configuration directory, lib. Creation Submit a new entry Create a collection. Four messages are supported for a required feature of POSIX conforming systems, and a fifth for a conditional feature. However by manhal it will use the full file name, which can make for hard to read listings.

  HCPL 0453 PDF

DejaGnu will log the name of each file of expect code found in the test directory. Each DejaGnu test is an expect script; the tests vary widely in complexity, depending on the nature of the tool and the feature tested.

For a small program, the spawned output could all fit in the buffer. DejaGnu is written in expect, which in turn uses tcl which is how the tests themselves are usually written. Before writing code using expect you should be fully familiar with TCL [1]. The tool s must be named. Strictly speaking the suffix. Timeout reduced to 3 seconds set timeout 3 runmytest “Simple test” “orelf-sim -f default. Navigation menu Personal tools Dejangu account Log in.

It runs a series of tests written in expect and reports the results of those tests. Table of Contents 1. So we should check for warnings or errors before we test for successful completion.

Dejagnu – Free Software Directory

DejaGnu has a number of global variables which are set to correspond to runtest command line arguments. For example for tests which cannot run on a particular target board. This is a GNU package: Version for TCL 8.